Skip to content
HeaterGuides
Water Heater

20 Gallon 110V Electric Water Heater for RV Trailers

On this page 7 sections
  1. 20 Gallon Electric Water Heater for RV Trailer Use
  2. How 110V Power Changes Recovery Time
  3. Running Cost And Shower Time
  4. What To Check Before You Buy
  5. When A Different Type Makes More Sense
  6. Before You Buy Or Call A Technician
  7. Questions People Ask
Quick answer
A 20 gallon 110V electric water heater can work in an RV trailer, but it won’t recover fast and it needs the right electrical supply. An electric water heater heats stored water with a resistive element, so on 110/120V power the element size limits how quickly the tank comes back after a shower.

Say your trailer has two people, one shower, and a 20 gallon tank with a 1,500 W element. After 10 to 15 gallons of hot water leaves the tank, recovery is slow enough that the second shower may need a break, which is just the heater being honest about its wattage.

That makes the real choice less about tank labels and more about power, duty cycle, and how much hot water you use at one time. A 110V unit can be fine for a sink, a hand wash station, or light trailer use; for back-to-back showers, it starts looking small very quickly.

20 Gallon Electric Water Heater for RV Trailer Use

20 galloon electric hpt water heater 110 volt for rv trailer: 20 Gallon Electric Water Heater for RV Trailer Use

A 20 galloon electric hpt water heater 110 volt for rv trailer can serve one modest shower or light sink use, provided the trailer has the right electrical supply. A 20 gallon electric water heater stores less hot water than a 50 gallon electric water heater, and a 50 gallon electric water heater is usually a poor RV fit unless the trailer has the space and power for it.

The 20 gallons describe the tank’s storage size; 110/120V describes the electrical supply feeding its heating element. A 1,500 W element is common on small plug-in heaters and draws about 12.5 amps at 120V, so recovery is slow compared with many 240V units. The tank can hold a useful reserve, but the element refills that reserve at a modest pace.

1,500 W
Common small-heater element size
At 120V, that element draws about 12.5 amps. The circuit, plug and heater nameplate must be suitable for the load.
TankPractical RV useMain limitation
20 gallonsOne modest shower, a small sink, or light-duty washingHot water reserve runs down quickly with back-to-back users
50 gallonsLarger fixed installation with heavier demandMore space, weight and electrical capacity than many trailers have
Tank size affects reserve; element size affects how quickly that reserve returns.
Myth
A larger tank alone decides how well an electric water heater performs.
Fact
Recovery rate matters just as much. A 20 gallon tank with a 1,500 W element may be ready for one shower, but several users can empty its useful hot-water reserve faster than the element can replace it.

If your need is hand-washing or a trailer kitchen sink rather than a shower, a compact under-sink tank may fit the job better than a full 20 gallon cylinder.

120V1500W Small Under Sink Tank 2.6 Gallon Water Heater Hot Storage,I…
For a sink-only hot-water point
120V1500W Small Under Sink Tank 2.6 Gallon Water Heater Hot Storage,I…
Product 1 stores 2.6 gallons and runs at 110/120V with 1,440–1,500W, making it suited to an under-sink RV or small wash station. It won’t provide the reserve needed for a full shower.
View on Amazon
Worked Example
Say one person takes a shower and then another person runs the sink for dishes. The first shower uses much of the tank’s usable hot-water reserve; the sink draws down what remains, and a second shower may need to wait for recovery. Three people using the shower back to back will expose the 1,500W limit quickly—small element, slow refill.
Tank storage20 gallons
Heating element1,500 W
Best fitOne shower or light sink use at a time
In short
Choose 20 gallons for an RV trailer with moderate, spaced-out demand. Choose a larger tank only after confirming the trailer can support its size, weight and electrical requirements.

How 110V Power Changes Recovery Time

110V electric hot water heaters recover slowly because watts equal volts multiplied by amps, and a normal RV outlet or 120V circuit limits both available voltage and practical current. A 1,500 W element on 120V draws about 12.5 amps, leaving limited power for reheating the tank.

12.5 A
Draw of a 1,500 W element at 120V
That load is near the usable limit of a standard 15-amp branch circuit, so the water heater needs the circuit and breaker specified by its manufacturer.
SetupWhat the power meansRecovery effect
1,500 W at 120VLower heating powerThe tank reheats gradually after hot water leaves
Higher-wattage unit at 240VMore electrical power is availableRecovery is faster when the circuit, wiring and heater support it
Tankless electric heaterHeat is made while water flowsThe required electrical capacity can be far beyond a simple 110V outlet
Voltage alone doesn’t set recovery speed; the element’s wattage does.

A 1,500 W element heats at a much slower rate than a higher-wattage 240V element. That doesn’t make you use less hot water; it only gives the tank less heat per minute. A 20 gallon tank can still run cold during heavy use when showers and sinks empty hot water faster than the element can replace it.

For a side-by-side look at the terminology, see electric water heaters 110V vs 220V explained. The short version is that a 220V heater usually needs a matching 240V circuit, not a clever adapter.

Can 110V run a 220V heater?
No. Do not connect a 220V water heater to 110V power or modify the wiring to make it fit. The element may underperform, the controls may malfunction, and the installation can become a shock or fire hazard.

If you’re searching how to install tankless electric water heater, start with the electrical requirement rather than the plumbing: check the model’s voltage, amperage, breaker and wire instructions, then have a licensed electrician handle new or upgraded circuits. Many whole-shower electric tankless units need far more capacity than an RV’s ordinary 110V receptacle can provide; a small point-of-use model is a different case and still must follow its listing and manual.

Running Cost And Shower Time

The most economical electric water heater for an RV trailer is usually the one that runs only as long as your hot-water routine requires; a 1,500 W tank costs in proportion to runtime, not tank size alone. For the examples below, the assumed electricity rate is $0.17 per kWh.

HeaterWattsPer hourPer day (2 h)Per month (30 days)
1,500 W heater running 2 hours per day1,500 W26¢51¢$15.30
Calculated at 17¢ per kWh. Monthly energy cost at an assumed $0.17 per kWh.
HeaterWattsPer hourPer day (4 h)Per month (30 days)
1,500 W heater running 4 hours per day1,500 W26¢$1.02$30.60
Calculated at 17¢ per kWh. Doubling runtime doubles the energy use.
HeaterWattsPer hourPer day (8 h)Per month (30 days)
1,500 W heater running 8 hours per day1,500 W26¢$2.04$61.20
Calculated at 17¢ per kWh. An extended runtime example for heavy winter use.
20 galloon electric hpt water heater 110 volt for rv trailer: Running Cost And Shower Time

The arithmetic is watts ÷ 1,000 × hours × price per kWh: 1,500 W becomes 1.5 kW, so every extra hour adds 1.5 kWh before the utility rate is applied. Dishes and brief sink use may keep runtime modest; repeated showers can keep the element working much longer.

In short
A 20 gallon electric water heater suits one shower at a time better than a queue of back-to-back showers. The tank supplies stored hot water first, then the element needs time to rebuild that supply.
1.5 kWh
Energy used by 1,500 W in one hour
That figure is the useful starting point for comparing runtime, utility rates and other electric heaters.

For an electric water heater for shower use, match the draw pattern to the tank: one person showering while others wait is workable, while several showers in a row call for recovery time or more storage. A heat pump water heater is generally the highest-efficiency electric water heater, but it needs suitable indoor space, airflow and condensate handling, so it usually isn’t a practical RV-trailer replacement.

From HeaterGuides · our own guidePage 15 sizes your next heater for your household and flow rate.Water Heater Owner's Toolkit: the printable guide and its Excel calculatorWater Heater Owner's ToolkitFix the common faults yourself, keep it running for years, and know when a repair is money wasted.No-hot-water flowcharts, gas and electricFlush, anode, relief valve and descaling stepsRepair-or-replace calculator (Excel)$14.99 $9.99Get it for $9.99See what's inside and watch the 2-minute video →18-page printable PDF + Excel calculator · instant download · 30-day refund

What To Check Before You Buy

Before buying, match the heater’s electrical nameplate, connections, dimensions, and mounting style to the trailer—not just the 20-gallon label. An electric water heater is identified by its nameplate, which shows voltage, wattage or amp draw, and required installation details; electric water heater recommendations should start there.

20 galloon electric hpt water heater 110 volt for rv trailer: What To Check Before You Buy

Switching from gas to electric is possible, but a gas water heater doesn’t become electric by changing the plug. A replacement electric unit needs the correct circuit, water connections, controls, and pressure-relief arrangement, so a licensed plumber or electrician should handle fixed wiring and gas disconnection where local rules require it.

Check These Before Ordering
Voltage: confirm the heater is rated for the trailer’s supply, commonly 110/120V, not 240V.
Amp draw: compare the nameplate load with the circuit’s usable capacity.
Breaker: follow the manual and local code; don’t assume an existing breaker is adequate.
Inlet and outlet connections: verify thread, pipe size, hot/cold orientation, and access for service.
Physical space: measure width, height, depth, door clearance, and room for the plumbing.
Mounting style: confirm the unit can be installed in the trailer’s approved vertical or horizontal position.
CheckWhat To MatchWhy It Matters
Electrical supplyNameplate voltage, watts, amps, and breaker requirementsA mismatch can trip the breaker or create an unsafe installation.
Water sideCold inlet, hot outlet, drain, and pressure-relief discharge arrangementThe fittings and relief plumbing must follow the manual and local code.
Cabinet fitOverall dimensions, service access, and mounting orientationA heater that fits on paper may block a panel or fail to mount securely.

A 1,500-watt heater on 120V draws about 12.5 amps, so the circuit has little spare capacity for other loads. Most 240V units and many tankless electric heaters need more electrical capacity than a basic RV hookup provides; a cheap electric 110v tankless water heater may still have limited flow because low voltage limits its heating power.

Don’t Force The Circuit
If the trailer can’t support the heater’s amp draw, choose a smaller storage heater or a different fuel source instead of changing breakers, using an extension cord, or improvising fixed wiring. Never cap or plug the temperature-and-pressure relief valve discharge.

For a broader buying shortlist, use the 20 gallon electric water heater buying guide after the nameplate and cabinet checks pass.

When A Different Type Makes More Sense

20 galloon electric hpt water heater 110 volt for rv trailer: When A Different Type Makes More Sense

A 20-gallon storage heater suits a trailer that has modest hot-water demand and a workable 110/120V circuit; a tankless or heat-pump design makes more sense only when its power, space, and operating conditions also fit. The phrase tankless electric water heater covers very different machines.

TypePower NeedRecovery SpeedBest Use Case
20-gallon storage heater110/120V version may fit a basic RV supply; verify the nameplateSteady but slow on 110/120VOne modest shower or light sink use with room for a tank
110V tanklessOften limited by the available circuit and heating wattageContinuous only at a modest flow rateSmall sink demand where cabinet space matters more than shower performance
240V tanklessRequires a 240V circuit with capacity specified by the unitFast recovery with enough power and flowA trailer or site already equipped for the required electrical service
Heat pump water heaterNeeds suitable electrical service, airflow, drainage, and installation spaceEfficient, but generally slower in cold airA larger, conditioned installation where efficiency outweighs compactness
Power requirements vary by model; use the nameplate and installation manual before planning the circuit.

A 110V tankless unit saves tank space, but low wattage can leave shower flow disappointing in cold weather. Electric tankless water heaters at 240V can heat water faster, yet the required circuit may exceed what a trailer pedestal or panel can supply.

Heatpump water heater vs electric water heater comparisons often favor the heat pump for efficiency, but many trailers lack the space, airflow, drainage, and mild surrounding air it needs. Cold air can slow recovery, and installation conditions matter more than the attractive efficiency label.

In short
Pick the 20-gallon tank when the trailer has ordinary 110/120V service and predictable, modest demand. Pick tankless only when space is tight and the circuit supports its real flow requirement; skip a heat pump when the installation area is cramped or cold.
Check The Site First
A product marketed as a cheap electric 110v tankless water heater may be useful at a lavatory sink but unsuitable for a full shower. Compare its rated flow at the temperature rise you need, not the word tankless on the box.

Before You Buy Or Call A Technician

Before buying, confirm the heater’s electrical circuit, plumbing location, leak path, and actual hot-water demand. Lower thermostat settings can save energy, but keep the tap temperature at or below 120°F to reduce scald risk. A Rheem electric water heater beeping may be reporting a control-board fault, high-temperature limit, or another condition; read the model’s manual before resetting anything. An electric shower water heater is a separate point-of-use appliance and may need a dedicated, higher-capacity circuit, so don’t assume the RV’s existing outlet can handle it.

Check These Before Spending Money
Match the heater voltage to the trailer supply and confirm the breaker size from the nameplate; never install a larger breaker just to stop trips.
Measure the tank location, door clearance, connections, and mounting surface.
Plan a drain pan or another safe leak path that won’t send water into the floor or wiring.
Confirm a reachable manual water shutoff on the inlet.
Estimate demand: one short shower and light sink use is different from back-to-back showers or dishwashing.
Confirm the pressure-relief discharge line can terminate safely and remain open.
Leave These Jobs To A Pro
Fixed electrical work, new circuits, 240V wiring, gas connections, and pressure-relief plumbing belong to a licensed electrician or plumber in most places. Never cap or plug the T&P valve, and shut off power before opening a heater panel.
A Beep Is Information
Write down the beep pattern, display code, and what the heater was doing. The manual can identify a temperature-limit trip or sensor fault faster—and cheaper—than guessing.

Start now by photographing the existing nameplate, breaker, water connections, and installation space; those four pictures give a technician the facts needed to say what fits.

Questions People Ask

Can I run a 20 gallon electric water heater on 110V in an RV trailer?
Yes, if the heater is rated for 110/120V and the trailer’s circuit can supply its nameplate load. Use the heater’s required breaker and wiring, and have a licensed professional handle new circuits or hardwiring. Never adapt a 240V heater to 110V power.
How long does a 20 gallon electric water heater take to recover?
Recovery depends on element wattage, incoming-water temperature, and the thermostat setting. As a rough example, a 1,500 W element needs about two hours to raise 20 gallons by 60°F before heat losses; a shower taken during recovery can outrun the tank.
Is a 110V electric water heater enough for a shower?
It can cover one modest shower if the tank starts hot and the shower flow is reasonable. A second shower soon after may require a wait because the 110V element adds heat slowly. Incoming water temperature matters most in cold weather.
Can you convert a gas hot water heater to electric in a trailer?
A gas heater usually needs replacement with an electric-rated unit rather than a simple element swap. The work can involve removing or sealing the gas connection, changing plumbing, providing the correct circuit, and meeting RV and local requirements. Have a licensed plumber or electrician handle gas, wiring, and vent changes.
What size breaker does a small 110V electric water heater need?
The heater nameplate and installation manual decide the breaker size; don’t choose one from the tank capacity alone. A 1,500 W load at 120V draws about 12.5 amps, so the existing circuit may not be suitable for other loads or for continuous operation. A technician should verify the breaker, wire size, and disconnect.
Should I buy a tankless electric water heater instead of a 20 gallon tank?
Choose tankless only if its 110V power rating and flow capacity match the shower you want in cold inlet conditions. A small 110V tankless unit may provide limited flow or only a modest temperature increase, while a 20-gallon tank stores hot water and can serve a short shower without heating the full flow instantly. Compare the unit’s required amperage and rated flow before switching.

Joye Editor

HeaterGuides covers home heating, water heating and HVAC: how the equipment works, what it costs to run, and how to use it safely.

More in Water Heater